I tried to fit my XFX 6800 XT And it was too small. I tried even removing the fan, but even then the metal coverings that hold the fans in place were getting in the way of the GPU. It was still a very clean and well organized computer case I loved it. I wish I could’ve kept it, but it was my mistake for not doing more research but I ordered another one from you guys.

Unit is very nice looking, decent quality and look. Swing out glass panel is very neat and good looking. Most things assembled well, lots of extra screw in case you loose one. Very nice lay out, easy to wire. My biggest complaints are the fans are not 4 pin PWM, they are the old molex type fans, so they can not be monitored or controlled by the motherboard. My PSU did not even come with the molex modular cable, so need to pay extra for that. Also the LEDS are molex type. I knew they LEDs were not ARGB, but I assumed that they could be controlled by the motherboard without the assigned, so the 3 wire instead of the 4 wire. But they are both just molex. The LEDs fine, but real bummer that the fans themselves are not controlled, means the unit is going to be a lot noisier than it needs to be. So the fans are basically throw away, making the unit not that cheap any more. Also, putting in a 650W ATX power supply with the 3/12 drie craddle is impossible, and the drive bay could have been slid a little and it would have bee fine. As is It just lays in the bottom unmounted.

Comes with a full complement of decent fans. Has plenty of room to build in. Hinged door is nice and glads is pretty thick. Lacks some cableanagement features, but that's what happens with budget cases. Still not dire how this is so cheap. The quality is really good.

Case Fans work properly fits 3060ti founders edition with ease. Fans stay quiet. Great Value Screws were labeled Dust filters are on top and on the bottom for your psu to go fan down.

This is one of the most feature-rich high-airflow cases you can get on a budget. The magnetic glass door which comes off without any screws is amazing, makes cleaning the case a breeze. The mesh front does a good job keeping dust and cat hair out of the system without sacrificing too much airflow. The fans included are fine, the molex centipede in the back is a bit of a pain to cable manage, but they leave you plenty of room to do it. As much as the back ports have pop-out designs for the PCIE slots, you can easily just slot the unused GPU ones back in, making it kind of a non-issue. If you're an enthusiast who wants the best RGB and fan control, this isn't the case for you, the RGB is static and the fans are too. But for the price, it's frankly unbeatable. A bit thin and flimsy in places, but a pleasure to build in, great size, great airflow, and, again, price tag.

I haven’t been able to build a pc in over 10 years, so I was pretty excited to put one together. I ordered the Montech X3 Mesh & I was initially pretty happy with it… until after I spent several days putting everything together & discovered that the front middle fan isn’t spinning, although the LEDs work. As far as everything else, I think it’s a great case for the sale price of $50. UPDATE: After contacting the seller Skytech, they offered me a partial refund because of the non-working fan. They also gave me an email address for the manufacturer Montech. After communicating with them via email, they sent me a replacement fan which arrived today. I haven’t tried replacing the defective fan yet, but I’m trusting that the new one will work. Overall, an excellent customer service experience in dealing with both companies. Changing my rating to add another star 👍 UPDATE #2: Montech did send me another fan, but it’s not the same one. It’s a 2-wire instead of 3-wire (which means it can’t be monitored/controlled by the mobo or software) & the LED lights are different enough that it’s noticeable. Not the end of the world & I do appreciate the fact that they sent one. Negatives: •Took 1 week to receive, which is a bit much •1 fan doesn’t spin (replaced)* •Fans are LED & not addressable RGB as the pictures might lead some to believe (although this is pretty clearly stated). •Fans have older style Molex connections that are all daisy chained together. •Cabling is fairly inelegant & comes held together with metal twist ties. •No PC speaker. •Materials aren’t the greatest. The gauge of the metal is pretty thin & a bit flimsy. •No rubber grommets in the cabling passthroughs •It’s perhaps a bit small for some ATX builds Positives: •Although the geometric aesthetic seems heavily “inspired” by Fractal brand cases, it’s a nice looking case regardless. •Pretty quiet at idle considering the 6 original case fans, the 2 additional fans I added & a 3 fan GPU •Good, simple design of the side panel, which is easily removable by just lifting it off, although the nylon ribbon loop used as a handle might turn some people off. •Side panel is tempered glass instead of plexiglass/plastic. •Small-ish mid tower case, but ATX motherboard, top mounted radiator in a push/pull configuration, 3 140mm, 5 120mm fans, a Corsair RM750 PSU & a 303mm Radeon 6650xt 3 fan GPU all fit in a nice looking package (although connecting the wiring & cable management is a bit of a chore). •Good airflow •It has a decent magnetic dust filter on the top, although that’s actually not great for airflow & will actually trap dust & restrict the hot air that you want to exhaust from your case. •I’ve seen some reviews that complain about the rear expansion card slots being the cheap kind that you have to bend or cut to remove, but the ones I removed when installing a GPU were secured with a slot & screw (much better). •Although the specs say it officially supports GPU’s up to 303mm I managed to squeeze in an MSI Gaming X Trio GeForce RTX 3080 which is 323mm with maybe even a couple of mm’s to spare. Conclusion: *After living with this case for about a month & the experiences that I had with both the seller & manufacturer, I’m adding the 5th star to my rating. It’s more of a budget case so you can’t expect perfection, but for $50 it’s an extremely good case & continues to perform very well.

Where to start. This case is just an amazing value at 64 bucks. I originally ordered the thermaltake view 270 but shortly after found this for 20 bucks cheaper and I'm glad I did. This is better than the thermaltake. Pros - included fans are great quality Building in this is so easy. Ample room for everything. White finish seems great. Rubber grommets for routing cables Airflow is good. Glass is crystal clear Front bottom io panel is perfect for desktop setups Pci screw rotating cover Reusable pci slot covers (not knockouts like the thermaltake) Cons - Only 1 I can think of and the metal is a bit flimsy but that's usually the case with this price range. Conclusion You just can't find this many features at this price. Montech is changing the game. Don't hesitate to buy this case you will not be disappointed.

Overall, for the price, a decent case that looks good without breaking the bank. As with anything, you get what you pay for, and this is not a top-tier case by any means... but it gets the job done without being a cheap eyesore. Easy to build in, room for future expansion, great airflow, is what it is for the price. Downsides: Fans and I/O. Very small and recessed buttons for RGB on/off and reset. Only one USB 3 and two USB 2 ports. Fans are...well, case fans. No speed control and no RGB control beyond on/off. Molex fans suck. Shipping from these guys was great! Came in a week faster than expected, and during the holiday season. Outstanding!

It arrived safely packed, I had no problem taking it out off the box. This is my first ever case to build and I did not have many problems. Screws are included and 3 screw adapters are also included for Micro ATX motherboards like in my case, therefore my Micro ATX fitted perfectly. The fans aren't very loud, they are pretty silent considering the amount of air the three 140mm fans in the front are taking in. The rgb lights in the fans are fixed lights and cannot be changed, only turned on or off which is a bummer but you quickly forget about it lol. I had a bit of trouble organizing all the cables, it really was a bit if a mess but with patience you can squeeze everything in. There're plenty of space for the PSU to go in as well and there's a small mesh below it for the fan. On the top of the PC there's a dust filter which you can remove and I recommend so the exhaust fans can pull out air easier. The quality of the case is OK, the metal is pretty thin so you need to be careful with it. The tempered glass door can be taken out and it doesn't need to be unscrewed or anything because it has a small fabric to open the door too. I couldn't add the built in wifi adapter that my pre build pc had so that's also a bummer, or maybe I can add it but I can't remove the back metals under the GPU. This is a very beautiful pc case overall and I recommend it for beginners like myself that don't have a lot of big things in it. If you have lots of bigger parts then this case isn't very spacious, I would reconsider something bigger.

This case is everything you need and with a stylish look. The only problem I have with this case is that they don’t include the adapter needed to connect the fans to the power supply. My power supply did not come with this connection, so now I have to spend another $8 to get a 2 pack, the second cable being wasted as I’ll probably never use it. Just make sure your power supply comes with a 4 pin molex cable and there won’t be a problem.